Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
blog:miniatures:eldar_display [2025/02/27 17:03] – [Trees] john | blog:miniatures:eldar_display [2025/02/28 15:51] (current) – john | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Eldar Forest/ | ====== Eldar Forest/ | ||
- | {{: | + | {{: |
==== Materials ==== | ==== Materials ==== | ||
Line 8: | Line 8: | ||
* 30mm extruded foam board | * 30mm extruded foam board | ||
* PVA glue | * PVA glue | ||
+ | * Contact adhesive | ||
+ | * Clear spray varnish | ||
* toilet roll paper | * toilet roll paper | ||
* hot glue | * hot glue | ||
Line 13: | Line 15: | ||
* 3-5" Deciduous set (TR1122) | * 3-5" Deciduous set (TR1122) | ||
* 2-3" Deciduous set (TR1121) | * 2-3" Deciduous set (TR1121) | ||
+ | * Woodland Scenics clumb-foliage medium green (FC683) | ||
+ | * WWS North Europe grass 2mm | ||
+ | * WWS North Europe grass 6mm | ||
+ | * WWS dry earth | ||
+ | * Assorted fine/coarse sand | ||
==== Building the boards ==== | ==== Building the boards ==== | ||
Line 19: | Line 26: | ||
{{: | {{: | ||
+ | |||
+ | {{: | ||
Covering with toilet roll paper soaked in watered down PVA glue (approx 10 parts PVA : 1 part water). This both protects the foam boards / gives the base a really tough finish when dry, but also gives the surface an uneven, less artificial texture: | Covering with toilet roll paper soaked in watered down PVA glue (approx 10 parts PVA : 1 part water). This both protects the foam boards / gives the base a really tough finish when dry, but also gives the surface an uneven, less artificial texture: | ||
Line 28: | Line 37: | ||
{{: | {{: | ||
==== Painting & Weathering ==== | ==== Painting & Weathering ==== | ||
+ | |||
+ | Base coat dark brown: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | Adding coarse sand and gravel around base of hills: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | Painting sand and gravel: | ||
{{: | {{: | ||
+ | |||
+ | Several layers of lighter browns applied via drybrush techniques to hills, rocks and gravel: | ||
{{: | {{: | ||
+ | |||
+ | ==== Grass ==== | ||
+ | |||
+ | Grass clumps stuck in place around hill edges: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | First layers of 2mm (centre area) and 6mm (edges) static grass: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | Second layer of static grass applied, along with little bits of dry earth: | ||
+ | |||
+ | {{: | ||
+ | |||
==== Trees ==== | ==== Trees ==== | ||
Line 48: | Line 84: | ||
{{: | {{: | ||
- | {{: | + | Clump foliage stuck to branches (branches coated in Evo-Stick contact adhesive) and then dusted with fine blended turf (dusted with varnish so that it will stick): |
+ | |||
+ | {{: | ||
+ | |||
+ | Larger trees glued in place: | ||
{{: | {{: | ||
- | ==== Grass ==== | + | No pictures of the smaller trees (2-3" variants), but they were done in exactly the same method. |
+ | ==== Monument/ | ||
- | {{:blog: | + | Portal monument cut from 10mm foam and sealed with PVA glue: |
- | {{: | + | {{: |
- | {{:blog: | + | Priming: |
+ | {{: | ||
+ | |||
+ | Painted and weathered: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | Static grass/moss added: | ||
+ | |||
+ | {{: | ||
==== Finished Display ==== | ==== Finished Display ==== | ||
+ | |||
+ | Complete, minus painted sides of the foam bases: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | Sides painted and monument terrain piece added: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | This shelf will probably need an extra LED lighting strip adding to make up for the shadows cast by the large number of trees. | ||
+ | |||
+ | === Additional Lighting === | ||
+ | |||
+ | With an additional loop of LED lighting installed on the shelf above, the diorama looks much better and should give the figures plenty of light when they are displayed: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | {{: | ||
---- | ---- | ||
[[: | [[: |