Differences

This shows you the differences between two versions of the page.

--- blog:386_pc [2021/05/08 15:28] – [Front Panel] john
+++ blog:386_pc [2021/05/17 20:43] – [LCD Display Config] john
@@ Line 28: / Line 28: @@
    * Using the 486 instruction set in a 386DX package
-   * Has 1KB of on-cache level 1 cache
+   * Has 1KB of on-chip level 1 cache
 It will be a nice test for those boards which are socketed to see the performance delta of just changing the processor and keeping everything else the same.
@@ Line 138: / Line 138: @@
 {{:blog:386:img20210508130046.jpg?200|}} {{:blog:386:img20210508130051.jpg?200|}} {{:blog:386:img20210508130055.jpg?200|}} {{:blog:386:img20210508130107.jpg?200|}}
-{{:blog:386:img20210508130158.jpg?200|}}{{:blog:386:img20210508132001.jpg?200|}}{{:blog:386:img20210508132222.jpg?200|}}{{:blog:386:img20210508135106.jpg?200|}}{{:blog:386:img20210508135123.jpg?200|}}{{:blog:386:img20210508135143.jpg?200|}}
+The spring for the power button was heavily rusted, so it got a dunk in a bath of white vinegar for a couple of hours:
-==== Painting ====
+{{:blog:386:img20210508130158.jpg?400|}} {{:blog:386:img20210508132001.jpg?240|}}
+Front panel re-assembled and then re-attached to the painted chassis:
+{{:blog:386:img20210508132222.jpg?200|}} {{:blog:386:img20210508135106.jpg?200|}} {{:blog:386:img20210508135123.jpg?200|}} {{:blog:386:img20210508135143.jpg?200|}}
+If it wasn't for that one bezel edge, I would have no second thoughts about leaving the front panel as it is... but compared to the newly painted chassis and the re-painted case (see below), well, it still stands out like a sore-thumb....
+==== Case Cover ====
+First thing I did was give the inside a quick spray in some white primer that I had left - it was a bit oxidised and messy:
+{{:blog:386:img20210508121149.jpg?200|}}
+For the exterior I used Plastikote RAL9010 White (satin finish):
+{{:blog:386:img20210508132812.jpg?400|}} {{:blog:386:img20210508132819.jpg?400|}}
+On it's own, the case looks absolutely fabulous. I'm quite keen on the colour; it's enough of an off-white to match the lighter-end of the spectrum of old AT computer cases.
+{{:blog:386:img20210508135516.jpg?500|}}
+However, placed next to the cleaned front panel:
+{{:blog:386:img20210508150757.jpg?500|}}
+==== Rethinking Things... ====
+I'm really not keen on painting the front bezel - other than that one edge which has yellowed it is in good condition and painting it would lose all of the button/indicator labels.
+My only real option at this point is to repaint the metal casing in a colour that now more accurately matches the front panel.
 ==== LCD Display Config ====
@@ Line 146: / Line 175: @@
 {{:blog:386:led_display_-_s-305_and_s-305h.jpg?400|}}
+By default, the case came configured with a high/low setup to show 33/16MHz:
+{{:blog:386:img20210511124436.jpg?200|}} {{:blog:386:img20210511124443.jpg?200|}}
+The rear of the display was set as shown:
+{{:blog:386:img20210511124550.jpg?300|}}
+I'll set the display to 40MHz high, and 10MHz low, since there isn't a standard for when turbo is disabled on 386 boards. That means I need to set:
+   * Units column (//0// in high mode, //0// in low mode)
+     * 3A 3B 3C 3D 3E 3F
+   * Tens column (//4// in high mode, //1// in low mode)
+     * 3B 3C 2F 2G
+==== Final Configuration ====
+{{:blog:386:img_2059.jpg?200|}} {{:blog:386:img_2058.jpg?200|}} {{:blog:386:img_2057.jpg?200|}} {{:blog:386:img_2056.jpg?200|}}
 ====== 386 Motherboard Shootout! ======