blog:386_shootout_forex

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
blog:386_shootout_forex [2021/03/09 22:13] – [74LS245N Removal & Replacement] johnblog:386_shootout_forex [2021/04/20 10:16] (current) – [Initial Testing] john
Line 16: Line 16:
  
 ==== Detailed Problem Images ==== ==== Detailed Problem Images ====
 +
 +I took these images after the board had arrived:
  
 {{:blog:386:img_1900.jpg?300|}} {{:blog:386:img_1901.jpg?300|}} {{:blog:386:img_1902.jpg?300|}} {{:blog:386:img_1903.jpg?300|}} {{:blog:386:img_1900.jpg?300|}} {{:blog:386:img_1901.jpg?300|}} {{:blog:386:img_1902.jpg?300|}} {{:blog:386:img_1903.jpg?300|}}
Line 71: Line 73:
 These UMB regions can then be used to load drivers and TSR's high, using the //highdvr// and //hightsr// utility included with The Last Byte memory manager similar to the MS-DOS commands //devicehigh// and //loadhigh//. These UMB regions can then be used to load drivers and TSR's high, using the //highdvr// and //hightsr// utility included with The Last Byte memory manager similar to the MS-DOS commands //devicehigh// and //loadhigh//.
  
 +=== BIOS ===
 +
 +BIOS from my motherboard:
 +
 +   * {{ :blog:386:forex_386_486.zip |}}
 ===== Repairs ===== ===== Repairs =====
  
Line 87: Line 94:
 {{:blog:386:img20210309201629.jpg?600|}} {{:blog:386:img20210309201629.jpg?600|}}
  
 +Fingers crossed that there isn't any more damage - there doesn't appear to be, so this looks like it has been caught in time. The battery header uses a diode as standard (part D4, just to the right of the header solder pads), so no chance of a battery pack getting charged and going bang. A standard 4-pin (+, N/C, N/C, Gnd) external pack will work fine.
 ==== ISA Socket Removal & Replacement ==== ==== ISA Socket Removal & Replacement ====
  
Line 97: Line 104:
  
 {{:blog:386:img20210309213520.jpg?200|}} {{:blog:386:img20210309213520.jpg?200|}}
 +
 +New 74LS245N DIP socket and 16bit ISA socket in position:
 +
 +{{:blog:386:img20210309222634.jpg?500|}} {{:blog:386:img20210309222717.jpg?500|}}
 +
 +74LS245N pin3 and ISA socket pin2 link wire in place:
 +
 +{{:blog:386:img20210310205822.jpg?400|}}
 +{{:blog:386:img20210310205908.jpg?400|}}
 +{{:blog:386:img20210310210556.jpg?400|}}
 +{{:blog:386:img20210310211603.jpg?400|}}
 +
 +{{:blog:386:img20210310211616.jpg?400|}}
 +{{:blog:386:img20210310213144.jpg?400|}}
 +{{:blog:386:img20210310215421.jpg?400|}}
 ==== ISA Socket Cleaning ==== ==== ISA Socket Cleaning ====
  
Line 104: Line 126:
  
 {{:blog:386:img20210309201702.jpg?500|}} {{:blog:386:img20210309201702.jpg?500|}}
 +
 +I'm pleased with these - other than the one with the missing pin, they've all come up really rather nice; hopefully just the one will need replacing now.
 +
 +===== Initial Testing =====
 +
 +Sadly, initial testing after reassembling the board after replacing the obvious components results in //no video// and //no error code beeps//. Processor and other chips were cold and didn't heat up, indicating no clock signal.
 +
 +First thing was to check all of the jumpers on the board, and many of them had been either removed or set to something //other// than what they were supposed to be for a 386DX-40. With those set correctly, and the programmable clock generator set to 40MHz the processor and other supporting chips now get warm, but still no output on screen or via the speaker.
 +
 +Next test is probably check with a POST diagnostic card and perhaps check some other clock signals.
 +
 +**[Update - 12/03/2021]** //POST diagnostic card arrived.//
 +
 +After initially having to repair two broken LED's on the __new__ diagnostic card, I eventually got it working and up and running in the Forex board. It confirmed that all voltages were present, and that the system reset behaviour was working, but no error codes are present:
 +
 +{{:blog:386:img20210312210910.jpg?500|}}
 +
 +Not sure how to proceed from here.....
 ===== Configuration ===== ===== Configuration =====
  
  • blog/386_shootout_forex.1615328038.txt.gz
  • Last modified: 2021/03/09 22:13
  • by john