blog:commodore_pet_restoration

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
blog:commodore_pet_restoration [2021/11/25 21:19] – [SuperSoft HR40 Connections] johnblog:commodore_pet_restoration [2021/11/25 21:26] (current) – [Cleaning] john
Line 49: Line 49:
 ==== Cleaning ==== ==== Cleaning ====
  
-{{:blog:blog:commodore:pet:img20211125200543.jpg?200|}}{{:blog:blog:commodore:pet:img20211125200549.jpg?200|}}{{:blog:blog:commodore:pet:img20211125202157.jpg?200|}}{{:blog:blog:commodore:pet:img20211125202201.jpg?200|}}+Cleaned the inside of the case and sprayed the spots that were starting to rust with a clear lacquer to stop it spreading:
  
-{{:blog:blog:commodore:pet:img20211125205816.jpg?200|}}{{:blog:blog:commodore:pet:img20211125205837.jpg?200|}}{{:blog:blog:commodore:pet:img20211125205930.jpg?200|}}{{:blog:blog:commodore:pet:img20211125205940.jpg?200|}}+{{:blog:blog:commodore:pet:img20211125200543.jpg?500|}} {{:blog:blog:commodore:pet:img20211125200549.jpg?500|}}
  
-Motherboard before and after:+Side of the case half done, with it partially cleaned its easy to see just how dirty it really was:
  
-{{:blog:blog:commodore:pet:img20211125203600.jpg?200|}} {{:blog:blog:commodore:pet:img20211125204321.jpg?200|}}+{{:blog:blog:commodore:pet:img20211125202157.jpg?500|}} {{:blog:blog:commodore:pet:img20211125202201.jpg?500|}}
  
-==== SuperSoft HR40 Connections ====+Rear of the case has some nasty glue residue from what looks to have been packing tape or possibly even duct tape. Not sure why anyone would have tape stuck to the back of the case??? Also cleaned up the really interesting original supplier case sticker.... they are //long, long// gone now.
  
-I took images of how the SuperSoft HiRes graphics board was connected, as it's not just inserted into a ROM socket, but has 3 chip test-leads clipped to the legs of 3 seperate chipsAlso someth+{{:blog:blog:commodore:pet:img20211125205816.jpg?500|}} {{:blog:blog:commodore:pet:img20211125205837.jpg?500|}}
  
 +Case all cleaned and back together. Looking much smarter:
 +
 +{{:blog:blog:commodore:pet:img20211125205930.jpg?500|}} {{:blog:blog:commodore:pet:img20211125205940.jpg?500|}}
 +
 +Motherboard before and after. I decided with the age of this thing not to go too wild - in the end I just used a soft brush to clean the majority of the dust away and then used alcohol to clean off the tarnished edge connectors. I didn't want to go to the extent of rinsing the entire board.
 +
 +{{:blog:blog:commodore:pet:img20211125203600.jpg?500|}} {{:blog:blog:commodore:pet:img20211125204321.jpg?500|}}
 +
 +==== SuperSoft HR40 Connections ====
 +
 +I took images of how the SuperSoft HiRes graphics board was connected, as it's not just inserted into a ROM socket, but has 3 chip test-leads clipped to the legs of 3 seperate chips.
 {{:blog:blog:commodore:pet:img20211125203812.jpg?500|}} {{:blog:blog:commodore:pet:img20211125203820.jpg?500|}} {{:blog:blog:commodore:pet:img20211125203812.jpg?500|}} {{:blog:blog:commodore:pet:img20211125203820.jpg?500|}}
  
 {{:blog:blog:commodore:pet:img20211125203833.jpg?500|}} {{:blog:blog:commodore:pet:img20211125203840.jpg?500|}} {{:blog:blog:commodore:pet:img20211125203833.jpg?500|}} {{:blog:blog:commodore:pet:img20211125203840.jpg?500|}}
 +
 + Also something that I did not notice earlier is a stacked (DRAM?) module, soldered on top of another module. This is also definitely non-standard:
  
 {{:blog:blog:commodore:pet:img20211125203849.jpg?500|}} {{:blog:blog:commodore:pet:img20211125203849.jpg?500|}}
  • blog/commodore_pet_restoration.1637875145.txt.gz
  • Last modified: 2021/11/25 21:19
  • by john