This is an old revision of the document!
IBM Thinkpad T43
Specs
- Intel Pentium-M 1.86GHz
- ATI X300 GPU with 64MB
- 15“ 1024×768 screen
- 2x DDR2-SODIMM slots (this came fitted with 2x 512MB DDR2-400 modules, 2GB is maximum)
- 2.5” PATA/IDE drive
- 2x USB 2
- vga OUT
- Parallel
- PS2 keyboard/mouse
- 10/100/1000 Ethernet
- Modem
- 3.5mm headphone out
- 3.5mm microphone in
- 1x Expresscard slot
- 1x Cardbus slot
- CDRW/DVD drive in Ultrabay module
Screen Versions
The T43 is available in a variety of screen sizes and resolutions. Typically the inverter, cable and LCD panel all need to be from the same size/resolution series:
Size | Resolution | Shorthand | Type | Cable Part # | Inverter Part # | Screen Part # |
---|---|---|---|---|---|---|
14“ | 1024×768 | XGA | TFT | 91P6941 | 27K9972 | 92P6765, 92P6731, 92P6733, 13N7044, 92P6726, 92P6759, 13N7024 |
14” | 1400×1050 | SXGA | TFT | 91P6942 | 27K9972 | 92P6737, 13N7046, 92P6760 |
15“ | 1024×768 | XGA | TFT | 91P6856, 91P6891 | 27K9974, 39T0359 | 92P6699, 92P6701 |
15” | 1400×1050 | SXGA | IPS | 91P6857, 91P6892 | 27K9976, 39T0361 | 92P6680, 92P6761 |
15“ | 1600×1200 | UXGA | IPS | 91P6858, 91P6893 | 27K9976, 39T0361 | 92P6753 |
Ultrabay Modules
- Ultrabay Slim SATA HDD Adapter: adds a 2.5” SATA bay (includes PATA to SATA chip). Part numbers 40Y8725, 45J7901, 45J7902, 26R9246, 26R9247
- Ultrabay Slim PATA HDD Adapter: adds a 2.5“ PATA/IDE bay. Part numbers 62P4554, 41U3148, 41N5661, 41N5660
Batteries
- 6 Cell, 4.8Ah: 92P1087, 92P1089, 92P1091
- 9 Cell, 7.2Ah: 92P1077, 92P1073, 92P1069
Images
Overview
Good Points
- Relatively good condition - limited amount of wear / scratches to case
- Nothing smashed or cracked
Bad Points
- Stuck GPU/CPU fan
- Discharged BIOS battery
- Missing hard drive / PATA only drives
- Backlight/inverter aged
Fixes & Repairs
Fan
The proper way to repair the noisy fan would be to replace it with a new part. In this case I didn't know if the machine was in a fully working state so I went the hack route…
First I soaked the fan bearings in isopropyl alcohol to clean out any residual oil/grease - the fan wouldn't turn when the machine first arrived. After getting the fan spinning freely again by hand I then drilled several small holes through the plastic central hub and carefully dripped in some lubricating oil. This clearly isn't the best way to solve the problem, and the sleeve bearing really isn't design to be serviced, however it did work, and the fan spins freely and is somewhat less-than-annoying in terms of sound level.
If the machine all checks out, then it may be worth replacing the fan with a new part.
Drivers & Utilities
- BIOS - Last official BIOS v1.29
- Platform Controller s/w - Last official Platform Controller software v1.06
- DOS PS2 utilities - DOS PS2 configuration utility for T4x series (LCD control, speed, brightness, fan control etc)
If BIOS and/or platform controller software is not up to date, the order to install them is BIOS then Platform Controller.
Audio
- Use VSBHDA - audio support is detected as ICH6.
Mouse
- Use Cutemouse - detects Trackpoint nub. Touchpad doesn't appear to respond.
Memory / UMB
- Disable USB ROM Floppy/CDROM boot support to claim back a portion of upper memory.
- Disable Network PXE ROM support to claim back a portion of upper memory.
With both ROM extensions above disabled, use D000 as the EMS page frame in EMM386/JEMMEX.
You can seem to use B000-B7FF with JEMMEX for a small amount of UMB memory - though be aware this disables support for really old monochrome DOS games. There are no other regions available.
Benchmarks
Test | Base Config |
---|---|
3DBench 1.0c | 625.8 fps |
Chris 3D Bench | 700 fps |
Chris 3D Bench SVGA | 127 fps (1) |
PC Player VGA | 538 fps |
PC Player SVGA | 63.4 fps |
Doom (low detail) | 147 realtics |
Doom (high detail) | 494 realtics |
Quake (320×200) | 360 fps |
Quake (360×480) | 142.9 fps |
Quake (640×480) | 60 fps |
Norton SI | 1236 |
Landmark CPU | 18000 MHz |
Landmark FPU | 24000 MHz |
Landmark Video | 37809 chr/sec |
- Ran in incompatible video mode